Anti-Reflective Film - Roll 1220/1500 mm width (for indoor)
| SGAR1500-RL / SGAR1220-RL |
| SGAR-RL is a wide width, roll type AR film for indoor use. It is widely used for large screen LCD protection cases, show windows, etc. Both 1220 & 1500mm width are available from minimum order of 2 meter. |
 |
 |
 |
|
||||
|
| ★ NOTICE 1 : SGAR is a product intended for indoor use. UV rays from sunlight can cause plastic products to deteriorate. For outdoor use, please use AR Film for Outdoor Use UVAR12SG / 15SG-RL. ★ NOTICE 2 : SGAR cannot be applied to resin/acrylic products. When applied to acrylic or other resin products, gas may be generated from the object and bubbles may form between the film and the object. Please refer to the following link for details. Caution when applying to plastic products. ★ NOTICE 3 : No Protective Layer on surface (AR) Side There is no surface protection film applied because it is a construction-use exterior film. Please use a special too (such as squeegee) when applying, and be very careful not to damage the surface with fingerprints or scratches. |
|
| Price |
| Item Code | Size | Unit Price |
| SGAR1220-RL (1220 mm width) |
2 - 4 meter | $ 156 / meter |
| 5 - 9 meter | $ 146 / meter | |
| 10 - 29 meter | $ 131 / meter | |
| 30 - meter | $ 122 / meter | |
| A4 size (25 x 30cm) sample | $ 25 |
| Item Code | Size | Unit Price |
| SGAR1500-RL (1500 mm width) |
2 - 4 meter | $ 175 / meter |
| 5 - 9 meter | $ 163 / meter | |
| 10 - 29 meter | $ 147 / meter | |
| 30 - meter | $ 137 / meter | |
| A4 size (25 x 30cm) sample | $ 25 |
| * Small free sample piece (about 8 x 8 cm) available. Please use Inquire form for request. |
 This product is shipped from Japan. Our standard shipping option is EMS,
however the maximum shipping size for EMS is 1.5 meters on one side. Therefore, we will use an alternate shipping company for the 1.5m size SGAR1500, resulting in a relatively higher shipping cost. We appreciate your understanding. For a shipping estimate, please get in touch with us via the inquiry form. |
|
| ★ AR film should be applied to both the front and back of the glass for full effect. The reflectance of a transparent object such as glass is about the same on the front and back, 4-5% on one side and 10% total on both sides. AR film reduces this to about 0.5% on each side, so if you put it on both sides, you can reduce it to 1% (one tenth), but if you only put it on one side, 5.5% (about half) remains. Although one side is also effective, it is best to apply it on both sides. |
||||||||||||||||||||||||
|
||||||||||||||||||||||||
| Not recommended for use with Multi-layered glass (double/triple glazing
glass) In the case of double-glazing, such as paired glass with two or more layers for the purpose of heat insulation or soundproofing, it is necessary to apply AR film on all surfaces (four surfaces in the case of double-glazing). This is not practical and we do not recommend. |
|
| Specification |
| Specification & Inspection Criteria | ||||
| Optical Characteristic (*3mm glass is a general value for comparison.) | ||||
| Item | Unit | Double side application | 3mm Glass | |
| Visible light (380-780nm) |
Transmittance | % | 96 | 90 |
| Reflectance | % | 0.9 | 8 | |
| UV Transmittance (300-380nm) | % | Less than 1.0 | 74 | |
| Sun light | Transmittance | % | 85 | 86.1 |
| Reflectance | % | 3 | 8.1 | |
| Absorption | % | 12 | 5.3 | |
| Shielding coefficient | 1 | 1 | ||
| Thermal conductivity W/(m | W/(m2K) | 6.0 | 6.0 | |
| Solar heat acquisition % | 88 | 88 | ||
|
| Physical Characteristics | ||||
| Item | |
|||
| Materia | PET | |||
| Effective thickness | 76μm | |||
| Width (mm) | 1220/1500mm | |||
| Tensile strength (%) MD | 102 | |||
| Tensile strength (N/25mm) MD | 151 | |||
| Adhesive strength (N/25mm) | 13.0 | |||
| * Actual measurement value, and not guaranteed values. | ||||
|
| Measurement condition; Double-sided application of SGAR on 3mm float glass (In accordance with JIS A 5759) ■ Shielding Coefficient: Relative value for the amount of heat entering a room from solar radiation. When 3mm float glass (with no AR film) is set at 1.00, this is the value when the film is attached to the glass. ■ Thermal Conductivity: It indicates the amount of heat per square meter that can be conducted in one hour when the temperature difference between the two sides is 1°C. ■ Solar Heat Acquisition: It indicates the amount of heat that flows into a room when the film is applied to 3mm float glass. The smaller this value is, the less solar heat flows into the room. Remedies and Limitations Should any product fail to perform as warranted or for any other claims arising from the purchase of products from us, our liability and your remedy are strictly limited to the purchase price or replacement, at our sole option, of the product sold. |
 |
 |